Titanium Gr1 vs Gr2 vs Gr5: Which One Should You Choose?

  • Release time: 2026-11-19

When selecting titanium, Gr1, Gr2, and Gr5 are often compared side by side. But practical selection isn't about finding the "best overall" grade—it's about answering one question: what is your part most afraid of?

 

 

Gr1Gr2Gr5

 

Key Takeaways


· Gr2 is the industrial default, offering the best balance of strength, corrosion resistance, formability, and cost.
· Gr1 excels in formability and corrosion resistance, but has the lowest strength and costs 15–25% more than Gr2.
· Gr5 (Ti-6Al-4V) is 2–3× stronger than Gr2, but harder to machine and costs 2–3× more.
· Purchase orders must specify oxygen content, delivery condition, and standard system—grade alone is not enough.

 


Gr1: When Formability and Corrosion Resistance Come First


Gr1 has the lowest oxygen content (O ≤ 0.18%) and a tensile strength of 240–370 MPa—the "softest" of the three. But that softness is a feature: it offers the best cold formability, can be deep-drawn and bent without cracking, and requires no post-weld heat treatment.


Typical applications: Titanium plates for plate heat exchangers, chemical equipment linings, electrolytic cells, deep-sea piping, ultra-thin medical foil.


Note: Gr1 costs 15–25% more than Gr2. If the part geometry is simple and doesn't require deep forming, that premium is wasted.

 


Gr5 (Ti-6Al-4V): When Strength Is the Priority


Gr5 has a tensile strength of 930–1100 MPa and yield strength of 860–960 MPa—2–3× that of Gr2. The trade-off: elongation drops to ≥12%, corrosion resistance is slightly lower, and both machining and welding are significantly more demanding.


Typical applications: Aerospace structural parts, engine components, load-bearing medical implants (artificial joints, bone plates), high-pressure vessels, racing components.


Note: Gr5 is not an "upgraded Gr2." If the failure mode is corrosion or forming cracks, Gr5's strength advantage is irrelevant.

 


Gr2: The Default Answer


Gr2 has a tensile strength of 345–480 MPa and yield strength of 275–345 MPa. Its corrosion resistance covers the vast majority of industrial media, its weldability is the best of the three (no post-weld heat treatment required), and its formability handles most常规 processing.


Typical applications: Pressure vessels, chemical storage tanks, seawater desalination equipment, pharmaceutical and food-grade piping, non-load-bearing medical components.


Selection logic: When there's no overriding reason to choose Gr1 or Gr5, Gr2 is the right answer.

 


Core Property Comparison


Property Gr1 Gr2 Gr5 (Ti-6Al-4V)
Tensile strength 240–370 MPa 345–480 MPa 930–1100 MPa
Yield strength 170–270 MPa 275–345 MPa 860–960 MPa
Elongation ≥24% ≥20% ≥12%
Cold formability Best Good Limited
Weldability Excellent, no PWHT Excellent, no PWHT Requires strict shielding and control
Corrosion resistance Best Excellent Good
Relative cost 1.15–1.25× Gr2 Baseline 2–3× Gr2
Typical applications Heat exchanger plates, linings, deep-drawn parts Pressure vessels, piping, tanks Aerospace structures, load-bearing implants

 


Four Things Your Purchase Order Must Specify


1. Standard system: ASTM B265 (plate/strip), B348 (bar), B338 (tube), etc.
2. Oxygen content limit: Gr1 requires O ≤ 0.18%; Gr2 requires O ≤ 0.25%. Do not specify grade alone.
3. Delivery condition: Annealed (M) or cold-worked (Y). Choose annealed for parts that will be formed or welded.
4. Gr5 ELI or not: Load-bearing medical or cryogenic applications may require ELI (Extra Low Interstitial). Standard Gr5 and ELI are not interchangeable.

 


FAQ


Q: What is the core difference between Gr1 and Gr2?
Oxygen content and strength. Gr1 offers better formability and corrosion resistance but lower strength; Gr2 is stronger and more widely used.


Q: Is Gr5 better than Gr2?
Not "better"—different. It's much stronger but less formable, harder to machine, and more expensive. It depends on what your part is most afraid of.


Q: Is specifying "Gr2" enough on a purchase order?
No. You also need to specify the standard, oxygen content, delivery condition, and product form. Otherwise, the supplier can legally ship to the loosest tolerance—which may not meet your design assumptions。

 

If you're choosing between Gr1, Gr2, and Gr5 for a specific part, send us the media type, load nature, whether forming or welding is involved, and target cost range. We'll help you work through the selection logic and provide the corresponding grade recommendation and procurement specification checklist.

If you're choosing between Gr1, Gr2, and Gr5 for a specific part, send us the media type, load nature, whether forming or welding is involved, and target cost range. We'll help you work through the selection logic and provide the corresponding grade recommendation and procurement specification checklist.

 

Contact Us:

Email: sales@globaltigroup.com

The team can walk through your specifications, confirm certifications, and arrange fast delivery for your next order.

 

about us通用

 

 

 

 

 

 

 

 

Copyright © 2025 Deko Corporation Ltd. All Rights Reserved.    备案号:陕ICP备08001158号-4 技术支持:兄弟网络

online service

Hello, I am the online customer service

X